Starter Batteries
No results
Sorry, your search returned no results.
Your cart
Your cart is empty
Sorry, your search returned no results.
All vehicles powered by a conventional combustion engine must be started by an external drive. In older models, starting with a kick starter or hand crank was common. Today, almost all vehicles have a starter operated by a battery. The design of the battery used depends on the respective requirements. In principle, however, similar criteria should always be applied when selecting a starter battery. Whether for cars, commercial vehicles, motorcycles, scooters, boats, quads, jet skis or ride-on lawn mowers - the choice of the right battery depends on the specific requirements.
This article highlights the currently common versions and the peculiarities of their use.
First, it is important to distinguish between batteries for starting an engine and those for providing power for the driving system or maintaining other electrical systems. When used to power vehicles, they are referred to as drive or traction batteries. The power supply of the onboard network is usually provided by similar battery types, which are also used as starter batteries.
Generally speaking, a starter battery is intended to start an internal combustion engine quickly and reliably. This can be the main drive or a starter motor. Typically, smaller engines are usually started directly, while heavier ones are started via a starter motor, especially in older models. To perform the start, an electric starter must be supplied with a high current. This is necessary so that it can generate enough power to overcome the self-resistance of the engine and accelerate it to a minimum speed.
Several different models are offered for this purpose. The simplest are the typical lead-acid batteries, which are still considered the standard. The principle is that lead and lead dioxide plates are alternately immersed in sulfuric acid. Each of these cells delivers a voltage of around two volts, so six cells provide the twelve volts commonly used today. They are affordable and operate reliably for several years. Compared to other battery types, they are quite heavy and have a low energy density relative to their mass. Their temperature dependence is also unfavorable, because extreme cold can restrict their function. Their advantage lies in their ability to deliver high currents for short periods, which is ideal for a starter battery. These batteries are regularly found in commercial vehicles and older passenger cars, especially when their high mass and size are not critical for operation.
A further development of these energy storage devices is the so-called EFB/AFB battery (enhanced flooded - /advanced flooded battery, improved (electrolyte) flooded battery). The construction is the same as conventional lead-acid batteries, but the changes are in the details. It can be charged faster, is more vibration-resistant, and is also less temperature-sensitive. For vehicles that are started frequently or exposed to strong vibrations, using this type is recommended as an alternative to conventional wet cells, even in start-stop automatics, these batteries are used.
In small vehicles, lead-acid batteries are often used in a sealed form. These can be used in any position and do not leak, which can be a major advantage for two-wheelers and boats. This design is also referred to as a VRLA battery (valve-regulated lead-acid battery, valve-regulated lead-acid battery). Although its power delivery is lower than that of other versions, it is still used to start motorcycles and boats. The advantage of not leaking in the event of a fall or capsizing outweighs the disadvantage of lower power.
For vehicles equipped with a start-stop automatic system, the use of a VRLA-AGM battery (VRLA-Absorbent Glass Mat, VRLA-Absorbent Glass Mat) is currently the best alternative. It combines the advantages of open designs with those of sealed ones. A cold start current that is around twice as high, combined with leak-proofness and a relatively affordable price, makes it the first choice.
The battery type is usually stated in the operating manual of the respective vehicle. This specification must be strictly observed when replacing it, otherwise malfunctions may occur. The design, voltage in volts (V), capacity in ampere-hours (Ah), and of course the cold start current in amperes (A) must match. Only with the capacity can a more powerful model be chosen, provided it fits in the battery compartment.
Despite their numerous advantages, lead-acid batteries are gradually being replaced. More expensive designs usually have a significantly longer service life and can easily store many times the energy. They are therefore suitable not only as starter batteries but can also be used to power electrical consumers without restricting their function.
Currently, lithium-ion batteries probably have the best weight-to-power ratio. They have a high energy density and are currently used primarily as traction batteries. Only where the lowest possible weight is required, such as in racing vehicles, do they also serve as starter batteries.
In principle, the battery should not be replaced by the user in newer models. Only in cases where no battery management system (BMS) is installed and where no error codes need to be cleared from the onboard electronics is it possible to change the battery yourself.
First, protective clothing should be worn. Safety glasses and acid-resistant gloves are the minimum requirement. Due to the high currents supplied by starter batteries, the dangers during replacement also increase. Vehicles have often caught fire because of a short circuit. Burns from tools that accidentally complete the circuit are also possible. Such accidents can be avoided with simple means.
When removing the battery, the ignition should first be switched off. Then the negative terminal connected to the vehicle is disconnected. This prevents current from flowing uncontrollably through the positive terminal. During installation, the negative terminal must be connected last. If there is a short circuit anywhere, numerous sparks will fly, and the cause can be searched for and eliminated.
It is often forgotten that electrochemical processes can occur at the contact points. For this reason, the terminals and connections are thinly coated with grease, which prevents corrosion.

Subscribe to our newsletter and receive all the latest news directly in your inbox.